• 3003 aluminum

    What’s The Difference Between 5052 & 3003 Aluminum?


    3003 aluminum sheet and 5052 aluminum?sheet are typically known as “Common Alloys” because they are two of the most widely specified alloys in the aluminum industry. But the differences between them show that even minor tweaks?in the composition can have a big impact when it comes to desired properties and end-uses. Here is a list of the differences between the 3003 and 5052 aluminum alloys.

    What Are 3003 Aluminum & 5052 Alloyed With?

    3003 is?primarily?alloyed with Manganese (Mn) and?the primary alloy ingredient for?5052?is Magnesium (Mg). In all, you’ll see that 3003 is an alloy of Silicon, Iron, Copper, Magnesium, and Zinc, while 5052 is an alloy of Silicon, Copper, Manganese, Magnesium, Chromium, and Zinc.?See the table below for the percentage?of alloying elements in each common alloy.

    Nominal Chemical Compositions

    Alloying Elements – Percent


    What Are?The Mechanical Properties of 3003 Aluminum & 5052?

    As you’ll see by the mechanical properties of 3003 & 5052, the subtle changes in alloying composition have a big impact on tensile strength.?3003 H14 has an?ultimate tensile?strength range?of 20 – 26 KSI, a yield of 21, an?elongation of 8.3%, and a Brinell hardness of 40, while 5052 H32 has an ultimate tensile?strength?range?of 31?–?38 KSI, a yield of 28, an?elongation of 12%, and a Brinell hardness of 60. See the table below to understand the difference in mechanical properties between the two alloys.

    Mechanical Properties

    Strength (KSI)

    Elongation % in 2 In.

    Alloy & Temper

    Ultimate?Min. – Max. (KSI)Yield?Set?0.2%1/16” Thick?” Dia.

    Brinell Hardness

    3003-014 – 19630%4028
    3003-H1217 – 231810%2035
    3003-H1420 – 262181640
    3003-H1624 – 30255%1447
    3003-H1827 –?–274%1055
    5052-025 –?311325%3047
    5052-H3434 –?4131101468
    5052-H3637 – 44358%1073
    5052-H3839?– –377%877

    How Do They Differ in Forming & Fabricating?

    In general, 3003 is fairly soft and has good corrosion resistance, good drawing, good workability,?moderate strength, and is weldable, while 5052 is stronger and has better corrosion resistance, good drawing, good formability, higher strength, and also is weldable.

    The best known and most widely used of the common alloys, with about 20% more strength than pure aluminum?1100, 3003 is considered a very practical general-purpose aluminum for moderate strength applications. Normally chosen for its excellent workability and drawing characteristics, it can be welded and brazed by all methods and has excellent corrosion resistance.

    The strongest non-heat-treatable sheet and plate in common use, 5052 is tough, strong, easily worked, and highly corrosion-resistant. Its versatility and strong value make it one of the most serviceable alloys. It has good drawing properties and a high rate of work hardening. Because of its resistance to saltwater corrosion, it is used in many marine applications.

    Comparative Characteristics and Applications

    Resistance to Corrosion


    AlloyGeneralStress-Corrosion CrackingWorkability (Cold)MachinabilityBrazeabilityGasArcResistance Spot & Seam

    How to Understand the Ratings

    Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion.?Alloys?with A and B ratings can be used in industrial and seacoast atmosphere without protection.?Alloys with C, D, and E ratings generally should be protected, at least on surfaces with joints.?This data was pulled from the 2013?Aluminum Standards & Data.?For more information, please refer to documentation by the Aluminum Association.

    How Do the Common End Uses of 3003 Aluminum & 5052 Compare?

    Common end-uses for 3003 aluminum include cooking utensils, food containers, chemical equipment, pressure vessels, general sheet metal fabrication, hardware, tanks, and cabinets. Common end-uses for 5052 include higher strength sheet metal fabrication, appliances, vessels, tanks, automotive, marine, food service, and medical equipment.

    3003 aluminum tanks

    How Much Do 3003 & 5052 Cost?

    Depending on availability and market conditions, 3003 is generally slightly cheaper on a per pound basis. However,?the higher?density of 3003?may?cancel out the lower price. To calculate the weights of aluminum sheet, you would use the following formula:

    • Decimal thickness * width *?length?* density = aluminum sheet weight.

    3003 aluminum has a density of .099 pounds/inch cubed and 5052 has a density of .097 pounds/inch cubed. So, for example, to calculate the weight of?3003?aluminum?sheet?with a decimal thickness of .125 and?non-standard dimensions?of?48” and?82”, you would multiple .125 * 48 * 82 * .099, for a value of?48.71lb. You can already see how the higher density of .099 may offset the higher cost of aluminum alloy 5052. In this case, the 5052?sheets?would be 47.72lb. The larger the purchase, the larger the impact of the difference in density will be. 5052 and 3003 can also be purchased as coil, but in that?situation,?it would?normally?be?sold to scale weight.

    The Paradox of 3003 Aluminum & 5052

    When comparing 3003 & 5052 in more detail, it is clear that while the chemical compositions look similar, they are alloys that both have much in common and also substantial differences. And, yet, while 3003 and 5052 may be ideal for different applications, for example, you’ll see 3003 recommended for cooking utensils and 5052 for hydraulic tube, for many others they are in fact interchangeable, like in sheet metal work. To decide whether 3003 or 5052 is right for your project, we invite you to email?kmc-nonferrous@kloecknermetals.com?today. One of our representatives will help you make the best decision for you.

    Natalie Spira
    Natalie Spira is Kloeckner's Marketing Communications Manager. Previously, she was the CEO and Founder of Fraction Marketing, a marketing agency catering to ecommerce startups. Natalie holds a MBA from Tel Aviv University with concentrations in entrepreneurship and marketing and a BA in English from UCLA.
    3003 aluminum
    Recent News Posts

    What is Structural Steel Fabrication? Structural fabrication refers to the...


    We’re proud this week to shine a light on James...


    Aluminum alloys are known for their corrosion resistance, ductility, conductivity,...

    More posts
    Subscribe To Our Blog

    Get a quote



    Outdated or Unsupported Browser Detected

    The Kloeckner Metals website uses modern technologies. Unfortunately, your browser doesn't support those technologies.

    Download the latest version of one of these browsers to experience the site:

    Do Not Remind Me Later